| Issue Date | Title | Author(s) |
| 161 | 2021 | Optimization of Barrel Wall Thicknesses Used in Shotguns Through Finite Elements Method | Uğur, A.; Yakut, Rıfat; Düzcükoğlu, Hayrettin; Şahin, Ömer Sinan |
| 162 | 2022 | Optimization of Electricity Generation Parameters with Microbial Fuel Cell Using the Response Surface Method | Neşeli, Süleyman; Dinçer, Kevser ; Taşdemir, Şakir; Hayder, Mustafa Akram |
| 163 | 2021 | Optimization Study on Surface Roughness and Tribological Behavior of Recycled Cast Iron Reinforced Bronze MMCs Produced by Hot Pressing | Güneş, Aydın; Şahin, Ömer Sinan ; Düzcükoğlu, Hayrettin; Salur, Emin; Aslan, Abdullah; Kuntoğlu, Mustafa; Pimenov, Danil Yurievich |
| 164 | 16-Jun-2020 | Ön ayarlı tork emniyeti kilit tertibatı | Şahin, Ömer Sinan ; İmaş Makina |
| 165 | 2019 | Parametric Euler-Savary Equations For Spherical Instantaneous Kinematics | Acar, Osman; Şaka, Ziya ; Özçelik, Z. |
| 166 | 2019 | Performance comparison of optimization algorithms in LQR controller design for a nonlinear system | Önen, Ümit; Çakan, Abdullah ; İlhan, İlhan |
| 167 | 2022 | PERFORMANCE INVESTIGATION OF BIFACIAL PHOTOVOLTAIC PANELS AT DIFFERENT GROUND CONDITIONS | Aksoy, Muharrem Hilmi ; Çalık, Murat Kubilay |
| 168 | 2022 | Polinom tipi sabit çaplı kam mekanizmalarının kinematik analizi | Ayğahoğlu, Mert Eren |
| 169 | 2020 | Prediction of residual stresses in ball burnishing TI6AL4V thin sheets | Livatyalı, Haydar; Has, Ergül; Türköz, Mevlüt |
| 170 | 2021 | Prediction of Yoshida Uemori model parameters by the bees algorithm and Genetic Algorithm for 5xxx series aluminium alloys | Korkmaz, Habip Gökay; Toros, Serkan; Kalyoncu, Mete |
| 171 | 2021 | Production and thermal characterization of MWCNT reinforced polimethyl methacrylate (PMMA) nanofibers by electrospinning | Ekrem, M.; Özten, U,; Şahin, Ömer Sinan |
| 172 | 2019 | Proposal of a Harmonic Bees Algorithm for Design Optimization of a Gripper Mechanism | Acar, Osman; Kalyoncu, M. ; Hassan, A. |
| 173 | 2023 | Residual compressive strength of polyamide fiber-reinforced epoxy composites after low-velocity impact | Coşkun, Taner ; Yar, Adem; Demir, Okan ; Şahin, Ömer Sinan |
| 174 | 2019 | Saf suyun alüminyum-kompozit levhaların yapıştırma bağlantılarındaki naylon 6.6 nanofiber takviyeli yapıştırıcılara etkisi | Tatar, Ahmet Caner |
| 175 | 2022 | Selectively Reinforced Functionally Graded Composite-like Glass/Carbon Polymer Nanocomposites: Designed for Efficient Bending and Impact Performance | Demir, Okan ; Tatar, Ahmet Caner ; Eskizeybek, Volkan; Avcı, Ahmet |
| 176 | 2018 | Serbest yüzey ve bir küre art izi arasındaki etkileşimlerin araştırılması | Doğan, Sercan ; Özgören, Muammer; Okbaz, Abdulkerim; Şahin, Beşir; Akıllı, Hüseyin |
| 177 | 2021 | Simulation and arduino hardware implementation of dc motor control using sliding mode controller | Maarif, A.; Çakan, Abdullah |
| 178 | 2023 | Solid Particle Erosion Behavior on the Outer Surface of Basalt/Epoxy Composite Pipes Produced by the Filament Winding Technique | Demet, Seyit Mehmet ; Sepetcioğlu, Harun; Bagci, Mehmet |
| 179 | 2022 | Solid Particle Erosion Wear Behaviors of Recycled PA 3200 GF Powders Produced by Selective Laser Sintering Method in Different Abrasive Environmental Conditions | Bağcı, Mehmet ; Demirci, Musa; Nesimioglu, Baris Samim |
| 180 | 2021 | Strength and Modal Analysis of Mobile Robot with Klann Walking Mechanism | Kavlak, Koray ; Taner, Y.O. |
